#Memeo instant backup purge deleted files drivers# For most purposes, this dump file is the most useful. It is smaller than the complete memory dump file, but it omits only those parts of memory that are unlikely to have been involved in the problem. If a second problem occurs and another kernel memory dump file (or a complete memory dump file) is created, the previous file is overwritten when the Overwrite any existing file setting is checked. Small memory dumpĪ small memory dump records the smallest set of useful information that may help identify why your computer stopped unexpectedly.
#Topcon gpt 3007n windows
This option requires a paging file of at least 2 MB on the boot volume and specifies that Windows 2000 and later create a new file every time your computer stops unexpectedly. #Memeo instant backup purge deleted files windows#
The Kernel-mode call stack for the thread that stopped.The process information and kernel context (ETHREAD) for the thread that stopped.The process information and kernel context (EPROCESS) for the process that stopped.The processor context (PRCB) for the processor that stopped.The Stop message and its parameters and other data.This dump file type includes the following information: A history of these files is stored in a folder.
This kind of dump file can be useful when space is limited. However, because of the limited information included, errors that were not directly caused by the thread that was running at the time of the problem may not be discovered by an analysis of this file. If a second problem occurs and a second small memory dump file is created, the previous file is preserved. Each additional file is given a distinct name. For example, Mini022900-01.dmp is the first memory dump generated on February 29, 2000.
#Topcon gpt 3007n series
Aeroqual Series 900 Fixed Monitor with Temp/RH sensor built in $405.00.Aeroqual Power Adaptor for S-Series Monitor $65.00.
#Topcon gpt 3007n Pc
Monitor to PC Cable for Aeroqual S-Series Monitor $80.00.Sensors (Geotechnical, Structural, Environmental).Type 2 Sensor Heads for Series 930 Fixed Monitor.Sensors for outdoor air quality monitors.Sensor Heads for the SM70 Fixed Monitor.Sensor Heads for Series 900 Fixed Monitor.Accessories for outdoor air quality monitors.Accessories for indoor air quality monitors.You can go ahead and hit measure and we can measure the relative coordinate of that prism from our total station (AMTS) based on this point that we said we are occupying in a very close to true northeast grid. And now we have set our current angle to 113 degrees.We are going to hit search to make sure our total station is locked on the dead center of that prism.Now the current angle is 24 degrees, is the current horizontal angle.We are not going to put in the true coordinates.Here, we are just going to be orienting the grid to the true northeast.] Now for the coordinate that we use, we are going to choose, in this case, an arbitrary coordinate, but we could use a specific one if we want to.So, to do that, to go back to the main menu, we are going to hit menu, we are going to hit coordinate, hit occupy setup.So the next thing that we are going to want to do is now we just need to set the horizontal circle of the automated total station to that angle.Subtract the current magnetic declination of 13 degrees and we get 113 degrees for our current horizontal angle.And if we take a measurement on our compass of the current facing of that prism, we get a measurement of 126 degrees. Now that we are perfectly in line with the automated total station still, we are going to take out our compass.And you can just barely make that out, but that white triangle is still visible when we put the automated total station sighting right over the prism. Now we are going to take a couple steps back from the total station so that the collimator, the white triangle, is still going to be visible right down the center there.Once we do that, once we aim at that prism, we will see that the sighting collimator, the white triangle, is visible when we look straight down the barrel there.The first thing that we are going to want to do is to aim our total station at the prism that we are going to use the center angle.Today we are going to be taking a look at setting the azimuth angle on your Topcon total station. Setting the Azimuth Angle – Topcon (AMTS) Total Station
0 kommentar(er)
